Your boat is a BIG investment. You want to protect it for years to come. It only makes sense that your boat lift system should last at least as long as your boat. If your boat lift is well-built and maintained, it can last 25 years or more. In general, a boat lift will last much longer if you take care of it.
Look at these areas as part of a regular boat lift maintenance schedule.
A properly sized boat lift will handle the weight of your boat plus the equipment you put in it. PWS will assist in selecting the proper size and type of boat lift for your hull and shoreline conditions.
The average boat up to 20′ will weigh in the 4 – 6,000 lb range. This includes the fuel, water, gas, motor(s). Don’t forget your passengers – including your friend – Big Bubba.
Don’t let people get in or out of the boat while it’s on the lift to avoid straining the system. When you’re not using your boat, remove the drain plug at the back of the boat. Rainwater can’t collect and add extra weight (roughly 8 lbs/gallon) if you do. Don’t forget to replace it before you go out again.
Lubricate your cables with penetrating oil instead of grease. Replace any cables with rust spots, broken strands, fraying, or kinks. Grease the lift pulleys if required. Be sure to check the nuts and bolts to ensure tightness.
Boatlift cable backlash
Check your winch drum as the cable is winding onto it to avoid slack, misalignment, and uneven wear. Never allow your lift cables to go slack. A slack line will result in damage to the system. It’s like a backlash on a fishing pole, only with a rigid steel cable. It can be challenging to unravel.
Never use a screwdriver or hit the cable with a hammer in an attempt to release the line. You’re almost guaranteed to cause severe damage.
If your boat lift has a motor, examine it for signs of rust or water retention. Ensure that any holes on the top of the motor or winch are closed.
The bottom holes must be open for proper drainage.
Inspect your gearbox and drive units regularly. Check for appropriate alignment, damaged cables, and areas that need lubrication.
Inspect your bunk carpeting for wear and tear and any wood underneath the carpet for cracks and rot. Lift beams should be kept out of the water when not in use. Better yet, get an aluminum/vinyl set and never have to replace the carpeting again.
Keep your hardware tightened, and be sure that the bunks line up correctly with your boat hull.
If you’re storing your lift in the off-season, remove the battery if you have a power hoist. Store it on a small piece of wood. Store your lift with the cradle or platform to the top.
Your boat lift protects your boat, so it’s essential to keep it in good condition.
Proper care and maintenance can help you avoid costly damage. Your dock and accessories need to be inspected for damage, also. Check your manufacturer’s guidelines for more specific care instructions.
It’s up to you to stay within the manufacturer’s specifications. Staying within those specs is crucial.
Even lifting a boat with the wrong hull design can cause damage. Never add more weight to your boat while it’s on the lift.
Entering or exiting a boat while it’s on a boatlift can be very dangerous. Ensure you have proper weight distribution when lifting.
Cables are usually made of stainless steel and need lubrication. Regularly apply penetrating oil or chain and cable fluid to reduce abrasion.
Make sure not to use grease on the cables. Grease traps moisture inside the cable strands. However, boat lift motor components and pulleys usually require grease.
Since you’re lubricating your lift, check for damaged cables that need to be repaired, replaced, or tightened.
Boat docks and lifts are still susceptible to water-related damage. Lift beams and bunks can be damaged by a boat coming in “hot.” When docking, check your speed, so you are not going faster than you are willing to hit the dock.
Keep your lift out of the water as much as possible. Small amounts of rust can be ground off and touched up.
Never place a plastic bag or cover over the winch and/or motors in the winter. Condensation will form inside and cause excessive damage.
Uneven wear can shorten cable lifespan, so keep an eye on the cable alignment. Make sheave alignment part of your regular inspections. Keep an eye on the winder, drum, and spool.
If you notice a backlashed cable, slack, or other boat lift problems- STOP. Don’t go any further. Adjust the cables immediately. If you’re not sure of the alignment, contact the professionals at PWS.
Reminder – Use leather gloves to protect your hands when handling the cables.
Even off-season storage can contribute to how long your boat lift lasts. Store your boat lift with the platform up.
If you have a power hoist, remove the battery and store it inside on a small piece of wood.
Once the flood or storm has died down, clear any debris off of your dock and lift. Look for bent or twisted beams, damaged drives, or broken bunks on your lift. Look for bent or damaged bolts and loose fasteners.
Check the lift cables for kinks, abrasions, frays, or breaks. Do not operate your lift until those cables are repaired or replaced.
If your boat lift shifted during the storm, realign it and make it square with the dock. When there are high waves, make sure the boat is still in the correct position.
Consult your installation manual or PWS for more information about adjustments. Even if everything looks good, make sure that you perform a test run of your lift. Check for any problems before you get back to boating.
At times large objects, like logs or other debris, strike your boatlift during the night or when you are away. Always look for damage if there was a storm.
ShoreMaster boat lifts are made with premium components. They make the best equipment to protect your boat.
Invest in the best boat lift brand to protect your boat – ShoreMaster.
Pier & Waterfront Solutions, 7325 St. Hwy 57, is located 3 miles south of Sturgeon Bay. Go 1 mile PAST the intersection with County MM (heading north). Look on the right at the intersection of Idlewild Road and Hwy 57.
Pier & Waterfront Solutions remains “open” year-round.
The Covid-19 virus is waning thanks to the population getting vaccinations. We hope that the remaining people will get the vaccine to help stop the spread of this deadly virus. We will continue to conduct as much business as possible by email, text, or phone to do our part to keep people safe.
Site visits continue as usual. When making in-person contacts, we follow “social distancing” guidelines when possible by doing any face-to-face contact outdoors.
Red Tag
PWS‘s display area is always open for you to examine at your leisure. All displays available for sale have a numbered, red tag on them. Want more information on something you saw in our yard? Please reference that number when you inquire.
PWS provides estimates by email to make the process faster, safer, and paperless.
Call, message, or email Jerry with any questions.
Jerry Englebert
Your boat lift is in the water, and you are ready for a great summer of boating. Have you taken your first cruise this year? Yes! It was a great experience – wasn’t it?
That is until you noticed the hole(s) in your canopy cover. Did the last storm cause a tear in your canopy? You can’t ignore it. It’s time to replace your top!
Your previous boat lift dealer went out of business, or you don’t remember what size canopy you need! Contact PWS.
By now, you’ve heard great comments about Pier & Waterfront Solutions. There are over 100 customer referrals on the PWS website, demonstrating the quality of our work. Those are not some salesperson’s words – they are actual, documented statements.
Mike W, Fish Creek
These young men (Alex and Tyler) did the best install I have ever seen! I am a perfectionist, and I could not have done a better job myself! Even the pipes that are across from each other are even in height where in the past the pipes were all at random heights,
We tipped the guys but I wanted you to know what a great job they did! Keep up the great work!! Mike W
Excellent Job
Hi Jerry, Enclosed is payment for the pier haul out this fall ….. They (the crew) did an excellent job under difficult conditions. Will call you next spring for re-installation. Dave W.
Great Job John K Door County
Crews do a great job. John K.
Awesome Service – Casey C.
Jerry, Thank you so much for the AWESOME service! Casey C.
Hi = just wanted to let you know your crew did a great job taking down our dock this year. You are all a pleasure to work with. Thanks David C.
QB Outstanding Project Work
Outstanding project work. Alex is magical on the forklift and Ben is a strong extra. Nice work, it’s exactly as I hoped it would turn out. QB
Dale R. Customer service is an art
Jerry, Customer service is an art. You have mastered the art. Thank you for your service! Dale R.
We appreciate you
I enjoyed talking to Keri
I enjoyed talking with Keri. She is very polite and personable. She relayed exactly what I wanted done and she will do well for your business. Please share this with her. Thanks Michael H
You also know that PWS can provide replacement parts for almost all dock and boat lift brands. But did you know PWS can provide replacement canopies for every brand of boat lift?
(alpha order)
Love your boat? Then you want to give it a dry home.
Many boat owners choose ShoreMaster Boat Lift Canopies to protect their boats. The quality and longevity of its products are synonymous with the name – ShoreMaster.
ShoreMaster Boat Lift canopies last for years, giving your boat the protection it needs and deserves.
Due to the quality of a ShoreMaster canopy frame, you don’t have to worry about them. But, the sun does deteriorate all canopy fabrics over time.
The two popular boat lift brands on the Door County peninsula are ShoreMaster and Shorestation. We’ll concentrate on those.
First, it’s important to remember that ShoreMaster has more than one length for each lift. Different fabrics and colors are also available for every model.
Telling us you have a model # SM 4010 lift is not enough. Here is the correct way to measure a replacement canopy for a ShoreMaster boat lift:
ShoreMaster Canopy Dimensions
Length: Measure from the frame outside edge to the outside edge, along the horizontal centerline. Do not measure up and over the top.
Width: Measure between the inside edges of the frame.
Shorestation lifts will have an extra factor to consider – The metal used on the canopy frame. Shorestation makes canopy frames with either steel or aluminum. It’s important to distinguish between the two before proceeding. The shape and mountings are different.
Older “legacy” models used steel for the frames. Later they began making aluminum boat lifts like the rest of the world.
Now we have the frame material down pat. Now we can ask the remaining questions. We’ll start with the aluminum lifts since they are the most popular.
Shorestation ALUMINUM Canopy Frames
Shorestation Aluminum Canopy Dimensions
Length: Measure the side rail and then add 2 feet to that number
Width: Measure between the inside edges of the frame
Now on to the Steel canopies.
Shorestation STEEL Canopy Frames
Shorestation Steel Canopy Dimensions
Length: Count the number of inner ribs
Width: Measure between the inside edges of the frame
NOTE: Were there ANY modifications or repairs to the canopy frame? If the answer is yes, it is vital to bring that information to our attention. Changes could result in an error. Custom canopy sizes are not returnable.
The best option is to have a PWS representative do a site evaluation by coming to your site. That way, you can rest assured that we have the correct information.
Look for the brand name on the frame or winch of the boat lift and call or send the information to us. Sending a photo helps also.
We will return a diagram of the frames to compare with your actual canopy frame. We will also show you how to take the precise canopy dimensions needed. It’s as simple as that!
If in doubt, ask PWS to send someone out to get the information.
It’s better to be safe than sorry – Call PWS Today!
Pier & Waterfront Solutions, 7325 St. Hwy 57, is located 3 miles south of Sturgeon Bay. Go 1 mile PAST the intersection with County MM (heading north). Look on the right at the intersection of Idlewild Road and Hwy 57.
Pier & Waterfront Solutions remains “open” year-round.
The Covid-19 virus is waning thanks to the population getting vaccinations. We hope that the remaining people will get the vaccine to help stop the spread of this deadly virus. We will continue to conduct as much business as possible by email, text, or phone to do our part to keep people safe.
Site visits continue as usual. When making in-person contacts, we follow “social distancing” guidelines when possible by doing any face-to-face contact outdoors.
Red Tag
PWS‘s display area is always open for you to examine at your leisure. All displays available for sale have a numbered, red tag on them. Want more information on something you saw in our yard? Please reference that number when you inquire.
PWS provides estimates by email to make the process faster, safer, and paperless.
Call, message, or email Jerry with any questions.
Jerry Englebert
Summer fun starts and ends at your dock and boat lift. Here, all your summer waterfront activities begin. Make your dock and boat lift look great and perform effortlessly.
There is no need to struggle to bring your boat back into your lift. PWS has the equipment to make life easier for you.
PWS features a full line of ShoreMaster boat lift accessories. We have a wide range of accessories to customize your dock and boat lift and fit your needs. Here are a few of the most popular solutions for your boat lift.
Vinyl Bunks
PWS offers top-of-the-line, vinyl-covered aluminum bunks that protect your boats hull. With vinyl-covered bunks, you’ll never have torn, unsightly carpeting to replace.
Vinyl does not hold the sand and debris like carpeting does and never needs replacement. Vinyl bunks protect your hulls’ finish and make a great boat lift accessory.
Is it time for you to step up? Contact Jerry now @ 920-493-04404
Bunks & Guide accessories
PWS also offers bow or full-length guides to hold your boat in the proper lifting position. The guides and rails make it much easier to control your boat in the waves.
The bow guide keeps your boat from overrunning the lift to ensure that it’s properly aligned. Waves will no longer push you too far forward on the boatlift.
You’re always appropriately balanced on the lift rack. See also.
Full-length guides mount on the lift rack to help you center the boat. Never get washed into the frames again. More importantly, the boat remains correctly centered at all times.
The boat guide and full-length guide use high-quality marine aluminum alloys and offer durability and protection for your watercraft.
For pontoon boat owners, we offer a welded aluminum rail kit option. They fit your craft’s unique shape.
Adjustable Motor Stop
Keep your boat from advancing too far into the lift by installing a motor stop. Motor stops let you position your boat on the lift with ease. This stop keeps your boat correctly balanced on the lift frames.
Isn’t time to call 920-493-4404?
Bow Guide Accessory
Here’s another alternative to keep your boat in the correct position. The adjustable Bow Stop accessory prevents you from overrunning your boat lift. The cushioned bumper on the frame prevents damage to your boat. You’ll always be in the exact position for storing your boat.
The bow stop or the motor stop will make your life easier. Call Jerry today!
PVC Guide on-Single set
A PVC vertical guide-on makes it easier to align and position your watercraft on the boat lift. The PVC guide-on means there is no maintenance. These guides allow your boat to slide along drive the boat rub rail to prevent touching the hull or marring the gel coat or decals. They gently push you back into position as the PVC turns. They are available in single or Double units.
Battery box tray accessory
Keeping your batteries out of the way is vital for safe and convenient operation. Never let a battery sit unprotected on your dock where children can touch them.
The battery tray mounts to the frame on the lift leg or a canopy frame. You’ll have a clean, clutter-free look with the batteries stored in the proper cases
Canopy Lift Loft
The universal size loft fits any canopy system. A loft can help keep your boating accessories dry and out of the way. The mesh is breathable and coated to inhibit mold growth. They are a great place to store your life preservers, canoe or kayak paddles, and more. Keep them handy, safe, and dry.
You’ll never have to find someone to carry your equipment to the boat again.
Pier & Waterfront Solutions, 7325 St. Hwy 57, is located 3 miles south of Sturgeon Bay. Go 1 mile PAST the intersection with County MM (heading north). Look on the right at the intersection of Idlewild Road and Hwy 57.
PWS is
Pier & Waterfront Solutions remains “open” year-round.
The Covid-19 virus is waning. We hope people will continue to get the vaccine to help stop the spread of this deadly virus. We will continue to conduct as much business as possible by email, text, or phone to do our part to keep people safe.
Site visits continue as usual. When making in-person contacts, we follow “social distancing” guidelines when possible by doing any face-to-face contact outdoors.
Red Tag
PWS‘s display area is always open for you to examine at your leisure. All displays available for sale have a numbered, red tag on them. Want more information on something you saw in our yard? Please reference that number when you inquire.
PWS provides estimates by email to make the process faster, safer, and paperless.
Call, message, or email Jerry with any questions.
Jerry Englebert
Vinyl bunks are a much better value than carpeted bunks. You bought your boat to enjoy yourself – not replace worn-out carpeting on the weekend.
Many boat and PWC lifts utilize carpeted bunks to support the vessel. These are an economical option and provide sufficient support for your boat or PWC (personal watercraft).
Vinyl Bunks
However, over time, the carpet on wood bunks becomes worn or frayed. This situation can create contact between the hull of the boat and the raw wood. Besides, sand and debris could be lodged in the carpet fabric. The sand will grind against the hull of the watercraft. It goes without saying this is not a condition you want. Any loose or frayed carpet should be replaced to prevent potential trip hazards too.
Do your carpeted boat bunks need replacement again this year? Vinyl bunks never require replacement.
Vinyl boat bunks may cost more than carpeted bunks initially but they are a better value over time.
Spring & Fall are excellent times to inspect the wood structure of the carpeted wood bunks. Wood, being a natural material, can become warped, cracked, or rotten. If you find any soft spots or warping of the wood material, replace the bunk before using it.
For more information on checking & servicing your lift, see https://wisconsinpws.com/lift-cable-maintenance/
Perhaps you’ve purchased a new PWC or boat and want the best bunk for your new purchase, consider ShoreMaster vinyl boat bunks.
ShoreMaster has used vinyl boat bunks for boats, PWC’s and pontoons for decades. The vinyl bunks will save you money in the long run because the aluminum channel will never rot or warp like wood. Plus, the vinyl never requires replacement like carpeting does. You’ll also save money and frustration because the vinyl material is less prone to wear than carpet,
Put simply; vinyl boat bunks are far more durable than carpeted bunks. The vinyl material used on ShoreMaster‘s vinyl boat bunks does not promote the adhesion of sand, and debris like carpet can, which means your boat or PWC will stay cleaner, longer.
Full-length vinyl boat bunks offer greater support than cradles. A much longer area is supported. The weight of your watercraft is distributed along the bunk’s length to prevent pressure points where your hull contacts the supports. When you have a choice between cradles, carpeted bunks, and vinyl bunks, you are better off in the long run with the vinyl boat bunks. When it comes to the total cost of ownership and resale value, vinyl boat bunks are the best value.
Vinyl boat bunks are available for all ShoreMaster boat lifts. If you are considering repairing a set of carpeted wood bunks, it may be wise to upgrade to vinyl bunks once and for all.
Pier & Waterfront Solutions (PWS) specializes in all ShoreMaster accessories for docks and lifts. We are located in the center of Door County at 7325 St Hwy 57 south of Sturgeon Bay at the intersection of Idlewild Road. Our staff looks forward to serving all of your waterfront needs.
The continued introduction of refinements keeps Shoremaster at the top of the best-in-class list.
Have friends or neighbors you believe should see this article? Email a link to this article – and Thank you!
You can visit Pier & Waterfront Solutions on Facebook also.
Pier & Waterfront Solutions has remained “open.”
While all this is going on, we are working to maintain the trusted service you expect. That’s important to us.
We are conducting as much business as possible by email, text, or phone. Site visits will continue as usual. When in-person contacts are necessary, we follow “social distancing” guidelines as closely as possible.
Call, message, or use this simple request form to get answers and quotes.
Thank you for allowing us to work with you – safely.
In last weeks article, (https://wisconsinpws.com/boat-lift-cable/) we discussed why your boat lift cable would not last forever.
This week we get into more detail and explain what you can do. We discuss the most critical causes of cable problems and what you can do to protect them.
There are two types of cable material used for boat lifts:
Rust on galvanized cable
Galvanized Steel is made of carbon steel which on its own is not resistant to rust. It is made corrosion resistant by running the cable through a hot bath of molten zinc. As long as the coating is on the wire “fibers,” it will resist the formation of rust.
Stainless Steel is also made of carbon steel. However, when mixed with about 10% chromium, it will form a stainless steel cable. It resists oxidation or corrosion. The chromium in the steel forms a layer of chromium oxide that promotes resistance to corrosion.
When the stainless steel wire is exposed to oxygen, the protective coating will REGENERATE. The anti-corrosion protection of the chromium maintains the resistance of the steel to rust.
Galvanized steel is less expensive than stainless steel due to the differences in the processing of each. Galvanized steel is durable, and each cable is sized to handle the loads created by your boat lift.
No – you can NOT increase the boat lift rating by merely increasing the size of the cable used. If you simply increase the diameter of the cable, you must also increase the size of the drum, or you risk early failure. The larger wire is stiffer and cannot bend around a smaller drum without damage.
Keep this information in mind if a neighbor or visitor wants to put their boat on your lift when it is empty. Know the weight of the new boat.
See https://wisconsinpws.com/boat-lift-calculations-part-4/ for additional information about cable maintenance.
Boat stern overhanging too far
Make sure your boat is positioned correctly on the lift. If it’s not far enough forward, it will put excessive weight on the rear cables and the frame structure. On the other hand, if the boat is too far forward, you may damage the lower motor assembly or break the front cables due to excess weight.
In general, a boat has most of its weight at the stern where the motor is. As a result, to maintain proper balance on your lift, the boat stern should be about 6″ to12″ from the lift rack. See the above article for more information.
When properly balanced, the weight is evenly distributed across the lift rack. A balanced boat prevents overloading one end of the lift.
Note – unusually long boats, may be an exception to the 6-12″ rule. You must be especially careful to find the proper balance. Proper balance will minimize potential damage to the cables.
1. Make a visual inspection of the cables regularly. It is helpful to do this when the lift rack is in its lowest position to expose more cable. Look for chafing, corrosion or a flat cable especially near the winch box.
Don’t forget – do this inspection with leather gloves on to protect your hands.
Boat Lift Cable Lubricant
2. At the beginning of the boating season, be sure to apply a burst of penetrating oil to the top of the cables around the winch drum. The penetrating oil will work its way down the wires as needed. Raise the rack halfway up and carefully apply another burst of penetrating oil to the winch drum. NEVER use grease on the cables. It traps moisture inside the strands. Do not be afraid to do it more often during the summer months, if you use the boatlift frequently.
Most quality lifts use Stainless Steel cables for a majority of cables and (1) galvanized cable as the main winch cable.
3. Watch the winch drum to ensure that the cable is wrapping smoothly on the drum.
Stainless steel lift cables also benefit from penetrating oil. We recommend this procedure in Spring, halfway through the boating season and again in Fall after removal.
To summarize, take care of your cables, and they may last for years. Remember, the cables and the winch do all the “work” on your lift. They do the lifting by raising the rack assembly with the weight of the watercraft on it. That’s a lot of weight so the cables must be well maintained.
In Spring and Fall (and at least once during the summer months), put a short blast or two of PENETRATING oil on the cables wrapped around the winch drum from the top of the winch. Do not soak the wire until it drips when in the water. You don’t want to contaminate the water. Use only penetrating oil as the lubricant.
NEVER use grease (it traps the moisture inside the cable accelerating its deterioration).
Cable maintenance begins with inspecting cables for frays and rust – Caution – wear leather gloves to prevent injury to your hands. Check near the top of the winch cable as this is the most common area for frays. Replace as needed, if corrosion is present.
Check the alignment of all cables on the pulleys. Simply follow the cables down until they wrap around a pulley. Are they On a pulley or is the cable off to one side? Call PWS if they are.
With your watercraft on the rack – check for any slack in the cables. All cables should be equal in tension. Contact PWS for adjustment, if needed.
Look for cable corrosion near the winch with the rack fully down (but without slack in the lifting cables.
Remember, the cables and the winch do all the “work” on your lift. They do the lifting by raising the rack assembly with the weight of the watercraft on it. That’s a lot of weight so the cables must be well maintained.
Pier & Waterfront Solutions (PWS) specializes in all ShoreMaster docks, lifts, and accessories.
We are located in the center of Door County at 7325 St Hwy 57, just south of Sturgeon Bay at the intersection with Idlewild Road. Our staff looks forward to serving all of your waterfront needs.
Call Jerry at 920-493-4404 or Email Jerry@wisconsinpws.com for more information.
